How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
Blog Article
Just how do you feel on the subject of Installing A Bathtub?
Setting up a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and occasionally, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably challenging project. If the old tub is readily accessible, the project can relocate speedily; if you have to open a wall to remove the old bathtub and also place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub as well as set in the brand-new one. See to it you have actually qualified yourself for the job and also fit attempting it. Rather than employing a contractor to take control of a halfway-completed task, it is much better to think about employing one prior to you start. Possibilities are you may need a specialist plumber to make tube connections.
This write-up will assist you install a new bath tub in your bathroom if you have actually already gotten a new bathtub as well as don't require to change the setup of your previous water supply pipes.
Your devices as well as product checklist need to make up the following:
Preparing for the Setup
First of all, the supporting framework provided with the bath needs to be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps unit to avoid pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its final position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of eliminating the existing taps can be quite problematic due to the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming during this process. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Before moving on to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are practical in uniformly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the tub until the level checks out level.
To install faucets, fit all-time low of the furthest adaptable faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water system as well as check all joints and brand-new pipework for leakages as well as tighten them if essential. Load the tub and also inspect the overflow outlet and also the typical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and also securing around the tub should wait until the bathtub has actually been utilized at least when as this will settle it right into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin making certain that the washing machines are in location in between the tap and also the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as fittings. They are marketed in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to permit the activity experienced when the tub is in use. The sealer can fracture rather early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is advisable to fit the tiles utilizing waterproof or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about How to Install a Bathtub? Leave feedback down the page. We'd be pleased to see your thinking about this piece. We hope that you visit us again before long. For those who liked our page kindly don't forget to pass it around. Many thanks for your time. Please visit our website back soon.
Schedule An Appointment
Report this page